I am an avid babywearer and especially love my soft structured carriers. I also love to sew and craft. I have decided to marry the two and create lots of fun goodies to go with my carriers! Because I know there are lots of you out there who are crafty like me, I've created some tutorials to help you out. Enjoy!

Sunday, October 25, 2015

Tula Hoodie Hood Pattern and Tutorial

clip_image002

The wait is finally over! After getting my computer to play nice with Blogger and taking care of family obligations, this has taken longer than I had hoped. But now, I present to you the Hoodie Hood Tutorial!!

I love the convenience of the flat hood and how easy it is to use on my Tula, but my kid HATES it! he will scream bloody murder when it's up if he happens to be awake. That flat hood also does little to nothing to help protect my kid's head from the sun or other elements unless it's hooked in and that's not happening - see above. 

If you're in the same boat as me or you just love that you can personalize your carriers with fun designs like the one pictured above, it's time to make a hoodie hood!

This pattern will fit a Tula™ in either standard or toddler size.This pattern is reversible, but keep in mind that the hood will either need to hang differently to show the other side, or you will need to apply two sets of snaps to change the direction. 

Here's your supply list:

· two coordinating fabrics (a fat quarter of each may just barely fit, but 1/2 yard is a safe bet)

· metal snaps (ykk 15 mm snaps are the ones used by Tula or #24 FASHION spring KAM snaps are the same size and should also work, though sometimes not as tightly)

· coordinating thread

· elastic cord (about 1 yard of 1/8" cord will be enough)

Now you will need to print the pattern here. You’re ready to start!

First, you will need to cut out your pattern pieces. Make sure that your fabric is folded in half such that the pattern is parallel to the fold. 

clip_image007

If the pattern in your fabric is not positioned this way off the bolt, you will want to make sure that you unfold and fold in the opposite direction. If you don't do this, the fabric design will be sideways on your hood!

clip_image009

clip_image011Place the pattern against the fold on the indicated locations. Cut around the edges of the pattern EXCEPT where it is marked as FOLD LINE.

Do this for both of your pieces of fabric. You will be left with two pieces that look like this.

clip_image013 clip_image015

Fold right sides together of each piece and sew along the top curve using a 1/4" seam allowance.

clip_image017

This is what it will look like at the edge by the fold. Be sure to backstitch here.

clip_image019 clip_image021

Press the seams open along the curve.

If you are planning to embellish the front of the hood in any way, you will want to do that now. Be sure to leave a small gap at the bottom to allow for sewing the outside and inside of the hood together. This is my finished front. (it will have propellers that snap on later).

clip_image023

Flip one of the pieces right sides out and nest the top and bottom fabrics of the hood together so that right sides are together. Pin in place, matching the seam line at the top of the hood.

clip_image025

clip_image027Cut two pieces of elastic about 17-18 inches long.

Sew around the sides and top of the two pieces of fabric, leaving a gap at the marked location of the pattern. Make sure to back-stitch before and after the gap to keep it securely closed when turning.

clip_image029

clip_image031

clip_image033

clip_image035

Press all of the sewn edges.

clip_image037

Top-stitch around the sides and top of the two pieces, leaving a gap where you left the gap on the inside seam.

clip_image039clip_image041clip_image043

Sew a casing for the elastic on the side about 1/2 inch away from the edge. Then sew inwards to the edge of the hood to connect to the topstitching.

clip_image045 clip_image047 clip_image049

Fold each piece of elastic in half and slide up through your casing.

Leave enough sticking out for your liking. I usually like around an inch or so.

Stitch along the bottom of your casing to keep the elastic in place, about 1/4 to 1/2 inch from the bottom. You'll want to sew over the elastic multiple times to prevent it from being pulled out with use. 

clip_image051

Trim any excess elastic from the bottom.

Separate the two sides of the elastic loop at the top. Sew a short distance between the two pieces of elastic in the casing. Make sure not to sew over the top of the elastic.

clip_image053 clip_image055 clip_image057

This prevents the elastic from sliding down into the casing when no reach straps are attached.

clip_image059

Cut a piece of material for the binding of the base. You will want it to be at least 3 inches wide by 9.5 inches long.

clip_image061

Press the sides in a quarter of an inch.

clip_image063

Fold in half lengthwise and press again.

clip_image065

Now fold each half in half and press one more time.

clip_image067

You'll be left with a strip that is about an inch tall with no unfinished edges showing.

clip_image069Mark the location on your hood for the pleat. This is found at the bottom of the pattern.

Also, find the center of your hood at the bottom open edge and mark with a pin.

clip_image071

Do the same with your binding.

clip_image073

clip_image075Fold the pleats into the center of the hood at the marked locations. Pin these in place.

clip_image077clip_image079

Line up the center of the hood to the center of the binding.

clip_image081

Pin across the bottom of the hood.

clip_image083clip_image085

clip_image087Sew up the side of the binding, across the bottom of the hood and then down the other side of the binding.

 

clip_image089

Now you're ready for snaps! Snap should be 8.5 inches apart. It’s always a good idea to measure your own Tula to make sure that this measurement is correct. There may be slight variations in this distance due to manufacturing differences. Measure half of the snap width from the center, in the middle of the binding, and mark with a pin or disappearing/washable fabric marker.

clip_image091

Measure your marks again to make sure that they are the right distance apart and adjust if necessary. It's important to get the distance apart right so that the hood will snap into your carrier correctly. When in doubt, err on the side of too far apart instead of too close together.

Follow the directions of your preferred snap setting device to install the snaps. You can use snap pliers, snap presses, or more simple mechanical tools to install the snaps. Repeat for the other mark.

clip_image093 clip_image095

You're done! If you've sewn with elastic, see my tutorial here to make your reach straps. If you used webbing or already have your reach straps made and want to embellish the ends, see the tutorial here!

As always, if you enjoyed this tutorial, please consider donating to help me write more! Thank you to those who have already made donations. A small donation will go a long way!



 

12 comments:

  1. May I know what size should I print the pattern in? A4? Thanks!

    ReplyDelete
    Replies
    1. I would like to know too, thanks!

      Delete
    2. The pattern is designed to print on standard 8.5"x11" paper which is US letter size and roughly equivalent to A4 I believe.

      Delete
  2. Where can I find the snaps? I've been searching for them with no luck.

    ReplyDelete
  3. Do you have any recommendations for making a toddler sized hoodie hood?

    ReplyDelete
  4. Do you have any recommendations for making a toddler sized hoodie hood?

    ReplyDelete
    Replies
    1. this tute is meant for both standard and toddler size Tulas :)

      Delete
  5. When I print out the pattern, it prints on two pages of 8.5 x 11 paper. Is that correct? Could you give me the dimensions of the pattern (at least the height) so I can verify that I have the correct size? Thanks and thank you for this great tutorial!

    ReplyDelete
  6. Do you have a video of this? I'm newer at sewing so it's easier for me to watch it and follow along. Thanks

    ReplyDelete
  7. Hello :) thank you for posting this. When I print the pattern, there is a thin line between where the pattern lines end and the paper begins. A gap between them. Please tell me I'm supposed to have trimmed this before taping the pieces together, because I did!

    ReplyDelete
  8. I have been surfing online more than three hours today, yet I never found any interesting article like yours. It is pretty worth enough for me. Personally, if all site owners and bloggers made good content as you did, the internet will be a lot more useful than ever before.
    baby bandana drool bibs

    ReplyDelete